Thermoplastic Starch / Cellulose Nanofiber Nanobiocomposite Foam: Investigation on Thermal and Mechanical Properties

Document Type : Complete scientific research article

Authors

1 null

2 Director of Technology Incubator of IROST

Abstract

Abstract
Background and Aim: In recent years, has been increased production volume of polystyrene foams. These foams are applicable in food and packaging industries. Growing environmental concerns have created a need to develop biodegradable materials. Starch is a widely available, renewable, low cost, biodegradable and thermoplast (TPS). For these reason starch generates a great interest at it is considered as promising alternative to synthetic polymers (as polystyrene). But poor mechanical properties is a limited parameter to use this polymer. One of the important ways to reduce this limitation, is improvement of the thermal and mechanical properties using of nanofiber cellulose as reinforcement of foam. But NFC gel is aqueous and it forms irreversible aggregates when dried. High moisture create big cells in foaming and effect on foam properties. This subject limite using of NFC (nanofiber cellulose) to prepare polymeric composites. The aim of current research is using NFC (nanofibercellulose) to prepare NFC/TPS nanobiocomposite foam by extrusion mixing for better dispersion of NFC in matrix polymer and investigation on thermal and mechanical properties of foam.
Materials and Methods: Granules powder of corn starch, glycerol, NFC gel, and azodicarbonamide have been used to make NFC-TPS nanobiocomposite foam. Glycerol (30, wt %) as plastisizer. NFC (0.5, 1, 1.5, wt %) as reinforcing agent and azodicarbonamide (0.2, wt %) as blowing agent (BA) were used. Raw materials were mixed in a co-rotating two screw extruder. Then TPS/NFC/ BA granules was prepared. Then by using of these granules, nanobiocomposites foams were prepared under hot press (temperature higher than degradation temp of BA). The morphology of the samples studied by FE-SEM. The tests thermogravimetry (TGA), differential scanning calorymetry (DSC), dynamic-mechanical- thermal analysis (DMTA) were done on TPS/NFC nanobiocomposite foams for determination of the thermal and mechanical properties.
Findings: FE-SEM images showed, that TPS/ NFC nanobiocomposite foam has higher and smaller pores in comparison TPS foam. This is due to nucleation effect of NFC. TGA showed thermal stability of TPS/NFC nanobiocomposite foam with increasing of NFC. DSC showed transition glass temperature has been increased with increasing of NFC content. The DMTA showed storage modulus and loss modulus increased with increasing of NFC conten but tan delta decreased. The reason of this result is formation microcellular foam and reinforcment of the cell wall of foam by NFC.
Conclusion: the results of research showed NFC improved thermal and mechanical properties of TPS/NFC foam. TPS/NFC foam had more unique and smaller in comparison of TPS foam.

Keywords

Main Subjects

References

1-Benezet, J.C., Davidovic, A.S., Bergeret, A., Ferry, L., and Crespy, A. 2012. Mechanical and
physical properties of expanded starch, reinforced by natural fibers. J. of Industrial crops and
products. 37: 435-440.
2-Bhatnagar, S., Hanna, M. 1995. Properties of extruded starch-based plastic foam. J. of
industrial crops and products. 4: 71-77.
3-Chen, M., Chen, B., and Evans, J. 2005. Novel thermoplastic starch-clay nanocomposite
foams. J. of Nanotechnology. 16: 2334-2337.
4-Dlouha, J., Suryanegara, I., and Yano, H. 2014. Cellulose nanofiber-poly (lactic acid)
microcellular foams exhibiting high tensile toughness. J. of Reactive and Functional
Polymers. 85: 201-207.
5-Ghanbarzadeh, B., Almasi, H., and Zahedi, Y. 2009. Biodegradable edible biopolymers. Amir
Kabir University of Technology tehran polytechnic press. Chapter 5.
6-Ghanbarzadeh, B., Almasi, H., and Entezami, Ali. 2010. Physical properties of edible
modified starch /carboxymethyl cellulose films. J. of Innovative food Science and Emerging
Technologies. 11: 697-702.
7-Guan, J., and Hanna, M. 2006. Selected morphological and functional properties of extruded
acetylated strch-cellulose foams. J. of Bioresource Technology. 97: 1716-1726.
8-Hu, F., Lin, N., Chang, P., and Huang, J. 2015. Reinforcement and nucleation of acetylated
cellulose nanocrystals in foamed polyester composites. J. of Carbohydrate Polymers. 129:
208-215.
9-Kaushik, A., Singh, M., and Verma, G. 2010. Green nanocomposites based on thermoplastic
starch and steam exploded cellulose nanofibrils from wheat straw. J. of carbohydrate
polymers. 82: 337-345.
10-Liu, D., Dong, Y., Bhattacharyy, D., and Sui, G. 2017. Novel sandwiched structures in
starch/ cellulose nanowhiskers (CNWs) composite films. J. of Composites Communications.
4: 5-9.
11-Lomeli-Ramirez, G.M.S., Kestur, G., Maniquez-Gonzalez, R., Iwakiri, S., Bolzonde Muniz,
G., and Sydenstricker Flores-sahagun, T. 2014. Bio-composites of cassava starch-green
coconut fiber: polymers. 102: 576-583.
12-Lopez, O., Zaritzky, N., Grossmann, M., and Garcia, M. 2013. Acetilated and native corn
starh blend films produced by blown extrusion. J of Food Engineering. 116: 286-297.
13-Lopez-Gil, A., Silva- Bellucci, F., Velasco, D., Ardanuy, M., and Rodriguez-perez, M.A.
2015. Cellular structure and mechanical properties of starch- based foamed blocks reinforced
with natural fibers and produced by microwave heating. J. of industrial crops and products.
66: 194-205.
14-Martins, I.M., Magina, S.P., Oliveira, L., Freire, L., Silvestre, A.J.D., Pascoalneto, C., and
Gandini, A. 2009. New biocomposites based on thermoplastic starch and bacterial cellulose.
J of composites sciences and technology. 69: 2163-2168.
15-Matuana, L., and Diaz, C. 2010. Study of cell nucleation in microcellular Poly (lactic acid)
foamed with supercritical CO2 through a continuous-extrusion process. J. of Ind. Eng.
Chem. Res., 49: 2186-2193.
16-Mi, H.Y., Jing, X., Peny, J., Salick, M.R., Peny, X.F., and Turng, L, Sh.M. 2014. Poly (ɛcaprolactone)
(PCL)/ cellulose nano-crystal (CVC) nanocomposites and foams. J. of
Cellulose. 21, 4, 2727-2741.
17-Mihai, M., Huneault, M., Favis, B., and Li, H. 2007. Extrusion foaming of semi-crystalline
PLA and PLA-Thermoplastic starch blends. J. of Macromolecular Bioscience. 7: 907-920.
18-Motahari, S., and Rezaeian, A. 2007. Physical and Mechanical Prorertice of Polymers.
Tehran University. 158p.
19-Nabar, Y., and Narayan, R. 2006. Twin- Screw extrusion production and Characterization of
starch foam products for use in cushioning and insulation applications. J. of Polymer
Engineering and Science, Doi 10. 1002/pen.2.292.
20-Sabetzadeh, M., Bagheri, R., Masoomi, M., and Ranjbar, M. 2013. Preparation and
investigation of properties of thermoplastic starch-low density polyethylen; Part 2: Water
Absorption behavior. J. of Chemistry and Chemistry engineering. 32: 3,25-30.
21-Svagan, J.A.S., Hedengvist, M., and Berglund, L. 2008. Reduced water vapor sorption in
cellulose nanocomposites with starch matrix. J. of Composites Science and Technology. 69:
500-506.
22-Svagam, J.A., Jensen, P., Dvinskikh, S., Furo, I., and A. Berglund, L. 2010. Towards tailored
hierarchical structures in cellulose nanocomposites biofoams prepared by freezing/freezedryind.
J. of Materials Chemistry. 20: 6646-6654.
23-Taghizadeh, A., and Favis, B. 2013. Effect of high molecular weight plasticizer on the
gelatinization of starch under static and shear conditions. J. of Carbohydrate Polymers. 92:
1799-1808.
24-Teixeira, E.M., Pasquini, D., Curvelo, A., Corradini, E., Belgacem, M.N., and Dufresne, A.
2009. Cassava bagasse cellulose nanofibrils reinforced thermoplastic cassava starch. J. of
carbohydrate polymers. 78: 422-431.
25-Wang, L., Zhou, H., Wang, X., and Mi, J. 2016. Evaluation of nanoparticle effect on bubble
nucleation in polymer foaming. J. of Physical Chemistry. 120: 26841-26851.
Journal of Wood and Forest Science and Technology
Volume 25, Issue 1
May 2018
Pages 61-74

Files

Share

How to cite

Statistics