دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Investigation on Forest Extend Changes Using Aerial
Photos and ASTER Imagery (Case Study: Border
Forests in South and Southwest of Gorgan City)
بررسی روند تغییرات سطح جنگل با استفاده از عکسهای هوایی و تصاویر ASTER
(مطالعه موردی: جنگلهای حاشیهای جنوب و جنوبغربی شهر گرگان)
1
20
213
FA
Journal Article
2012
07
16
The Hyrcanian forests have been highly exploited in recent decades by human impacts. Easy access, abundance and variety of valuable forest yields have led to population growth density, creation of new residential areas and deforestation activities. Change detection is one of the main methods of management and evaluation of natural resources. We investigated forest changes in southern surrounding of Gorgan city using satellite imagery and aerial photos for three different dates (1966-1994-2006). In order to produce forest extent maps for 1966 and 1994 years, aerial photos of mentioned years were georeferenced by topographic maps and ground control points and digital mosaic of aerial photos were done in GIS environment. Then, the forest extent map was produced by digitizing land use borders on digital photo mosaic for two dates. We used ASTER imagery to produce forest extent map in 2006. We found no radiometric noise in the imagery. Atmospheric correction of imagery was done using Cost method and geometric correction of imagery was accomplished by orthorectification method. Also synthetic bands were generated by suitable image processing methods including ratioing and principal component analyses. After selection of the best bands based on Bhattacharya distance, imagery was classified using supervised classification and neural network algorithms. For exploring of change detection, post classification comparison technique was employed. Results showed that severe changes were occurred in forest extent during the 41 years. Around 1250.8 ha of the extent of natural forests have been reduced, but 246.29 ha were just increased in this time duration. Hence, net forest extent reduction was 1004.5 hectare. Results also showed that rate of annual changes in the first time interval (1966-1994) was larger than second time interval (1994-2006).
در طول دهههای اخیر جنگلهای خزری توسط دخالتهای انسانی مورد تعرض قرار گرفتهاند. دسترسی آسان، فراوانی و تنوع محصولات جنگلی با ارزش منجر به افزایش تراکم جمعیت، ایجاد مناطق مسکونی جدید و فعالیتهای جنگلزدایی شده است. آشکار ساختن تغییرات یکی از روشهای اساسی در مدیریت و ارزیابی منابع طبیعی میباشد. این مطالعه تغییرات سطح جنگلهای جنوب شهر گرگان را در سه مقطع زمانی (1385-1373-1345)، با استفاده از تصاویر ماهوارهای و عکسهای هوایی مورد ارزیابی قرار میدهد. بهمنظور تهیه نقشه وضعیت گستره جنگل در سالهای 1345 و 1373، عکسهای هوایی سالهای یاد شده، رقومی و با استفاده از نقاط کنترل زمینی و نقشههای توپوگرافی زمین مرجع گردیدند. فتوموزاییک رقومی از طریق اتصال رقومی عکسها در محیط GIS انجام پذیرفت. سپس، نقشه گستره جنگل مربوط به این دو سال از طریق رقومیسازی مرز کاربریها بر روی فتوموزاییک رقومی بهدست آمده از عکسهای هوایی تهیه گردید. برای تهیه نقشه گستره جنگل سال 1385 تصاویر ماهوارهای سنجنده ASTER مورد استفاده قرار گرفتند. با بررسی کیفیت تصاویر، هیچگونه خطای رادیومتری مشاهده نگردید. تصحیحات مختلف، شامل تصحیح اتمسفری با استفاده از مدل COST و تصحیح هندسی با روش ارتو بر روی تصاویر انجام شد. باندهای مصنوعی با استفاده از روشهای مناسب پردازش تصاویر شامل نسبتگیری و تجزیه مؤلفههای اصلی ایجاد شدند. پس از انتخاب بهترین مجموعه باندی با استفاده از شاخص فاصله باتاچاریا، طبقهبندی تصاویر با استفاده از الگوریتم شبکه عصبی مصنوعی انجام گرفت. بهمنظور کشف تغییرات از روش مقایسه پس از طبقهبندی استفاده گردید. نتایج بهدست آمده نشاندهنده تغییر وسیع سطح جنگل به اراضی غیرجنگلی در طی مدت 41 سال میباشد. در طی این مدت 8/1250 هکتار از سطح جنگل طبیعی کاسته شده و فقط 29/246 هکتار به سطح جنگل افزوده شده است. به این ترتیب، در مجموع سطح جنگل به میزان 5/1004 هکتار کاهش یافته است. نتایج همچنین نشان داد که نرخ تغییرات سالیانه سطح جنگل طبیعی در طی دوره زمانی (1373-1345) بیشتر از دوره زمانی (1385-1373) بوده است.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Effect of Cuttings Type and Position on the Vegetative
Propagation of Yew (Taxus baccata)
تأثیر نوع و محل قلمهگیری بر موفقیت تکثیر غیرجنسی گونه سرخدار (Taxus baccata)
19
37
214
FA
Journal Article
2012
07
16
Common Yew (Taxus baccata) is one of the native and extinguishing speices at northern forests of Iran that is very important as a genetic reserve and, therefore, more studies are necessary for preservation and restoration of this rare forest speices. For having high value and complete preservation of gene structure, vegetative propagation is one of the suitable in use methods in this field. This research was carried out in order to achieve the most suitable direction, height and type of cutting from Yew crown. So, cuttings were collected from four main directions and two height of crown and planted in greenhouse conditions by heel and injured types as a factorial in randomized complete design. Data were analyzed with F test and Duncan multiple comparisons. Data variance analysis showed significant difference in 5 percentage error level in growth amount, new shoots and dried cuttings number. Evaluation of intercept effects was significant only for growth amount and number of new shoots. Based on the achieved data from this research, the highest growth of new shoots and growth amount belonged to cuttings of east direction, top height and injured type. Also, heel type cuttings from north direction and top crown height had the highest drying amount.
سرخدار (Taxus baccata) یکی از گونههای بومی و در حال انقراض جنگلهای شمال ایران میباشد که از لحاظ ذخایر ژنتیکی با اهمیت بوده و از اینرو مطالعات بیشتر در جهت حفظ و احیاء این گونه نادر جنگلی الزامی است. تکثیر غیرجنسی بهدلیل داشتن ارزش بالا در حفظ کامل ساختار ژنی یکی از ابزارهای مناسب مورد استفاده در این زمینه است. این پژوهش بهمنظور دستیابی به مناسبترین جهت، ارتفاع و نوع قلمه از تاج درختان سرخدار انجام گرفت. بنابراین، قلمهها از چهار جهت اصلی و از دو ارتفاع بالا و پایین تاج جمعآوری و به دو صورت پاشنهای و زخمی شده در قالب طرح فاکتوریل بهصورت کاملاً تصادفی در شرایط گلخانهای کاشته شدند. تجزیه و تحلیل دادههای بهدست آمده با استفاده از آزمون F و دانکن انجام شد. آنالیز واریانس دادهها بیانگر وجود اختلاف معنیدار در سطح 5 درصد خطا در متغیرهای میزان رویش، تعداد جوانههای نورسته و تعداد قلمههای خشک شده بود. بررسی اثرات متقابل، بیانگر وجود تفاوت معنیدار تنها در بین متغیرهای میزان رویش و تعداد جوانههای نورسته بوده است. براساس دادههای بهدست آمده از این پژوهش، بیشترین نمو جوانههای نورسته و میزان رویش در قلمههای جهت شرق، ارتفاع بالا و نوع زخمی شده مشاهده شد. همچنین قلمههای مدل پاشنهای از جهت شمال و ارتفاع بالای تاج بیشترین خشکشدگی را دارا بودند.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
The Effect of Paint Coating Types (Acid Catalyzed Lacquers
and Nitrocellulose Lacquers and Polyester) and Nano-particles
(Zycosil, Zycofil) on Withdrawal Resistance of Nail and Screw in Wood
بررسی تأثیر پوشش رنگی (سیلروکیلر و نیمپلیاستر براق) و نانوذرات
(زایکوفیل و زایکوسیل) بر ظرفیت نگهداری پیچ و میخ در چوب
37
52
215
FA
Journal Article
2012
07
16
The potential use of nano technology for improving of withdrawal resistance of nail and screw in wood was evaluated. For this, the maintenance strength of nail and screw was measured under dry and wet conditions for Poplar wood (Populus nigra) coated with common paints in furniture industry and nano-particles. Specimens with dimensions of 15×5×5 cm3 (L×R×T) were cut from Poplar wood (Populus nigra), Then, nails and screws were fixed on wood specimens, with respect to the ASTM-D 1761 standard. Afterward, specimens were separately coated with acid catalyzed lacquers and nitrocellulose lacquers and polyester paints, nano-zycosil and nano-zycofil reinforced polyester. Some specimens were dried in laboratory conditions and the others, under temperature of 103±2 oC in oven, Then, the maintenance strength of nail and screw was measured by a mechanical test apparatus (Instron). The results revealed that the minimum maintenance strength of nail and screw is for wet specimens and the maximum is for dry ones coated with acid catalyzed lacquers and nitrocellulose lacquers paint and Zycosil nano-particles. Zycosil nano-particles had better performance in comparison with Zycofil nano-particles. Increase in the maintenance strength of nail and screw in coated specimens with nano-particles reinforced paint is due to the formed rigid surfaces and decrease of water penetration in wood.
در این پژوهش، پتانسیل استفاده از فنآوری نانو در بهبود ظرفیت نگهداری پیچ و میخ چوب مورد بررسی قرار گرفت. برای این منظور، قدرت نگهداری پیچ و میخ در گونه چوبی صنوبر پوشش داده شده با انواع رنگهای رایج در صنعت مبلمان و نانوذرات در شرایط خشک و مرطوب اندازهگیری شد. از گونه چوبی صنوبر (P. nigra) نمونههایی به ابعاد 5×5×15 (T×R×L) سانتیمتر تهیه، و طبق استاندارد ASTM-1761D پیچ و میخها بر روی نمونههای چوبی نصب گردید. سپس، نمونهها با 4 نوع رنگ متفاوت با ترکیب: سیلروکیلر، نیمپلیاستر براق، نانو زایکوسیل و نیمپلیاستر براق تقویت شده با نانو زایکوفیل پوشش داده شدند، نمونهها در شرایط آزمایشگاهی خشک شده و قدرت نگهداری پیچ و میخ با استفاده از دستگاه تست آزمونهای مکانیکی اندازهگیری شد. نتایج نشان داد که بهطورکلی کمترین مقاومت به نگهداری پیچ و میخ مربوط به نمونههای مرطوب و بیشترین آن مربوط به نمونه خشک میباشد. بیشترین مقاومت به نگهداری پیچ در نمونههای پوشش داده شده با رنگ سیلروکیلر و نانوذرات زایکوسیل و همچنین بیشترین مقاومت به نگهداری میخ در نمونههای پوشش داده شده با رنگ سیلروکیلر، رنگ نیمپلیاستر تقویت شده با نانو زایکوفیل مشاهده گردید. افزایش قدرت نگهداری پیچ و میخ در نمونههای پوشش داده شده ناشی از بهوجود آمدن سطوح صلب بر روی چوب و کاهش نفوذ آب به درون آن میباشد.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Investigation on the Effects of Density, Adhesive Content and
Particle Size on Withdrawal Strength of Screw in Particleboard Made from Populus (Populus alba) Particles
بررسی تأثیر دانسیته، درصد چسب و اندازه ذرات بر ظرفیت نگهداری پیچ
در تختهخردهچوب ساخته شده از خردهچوب صنوبر (Populus alba)
53
69
216
FA
Journal Article
2012
07
16
Particle size, board density and adhesive content are the most important factors, influencing on physical and mechanical properties of particleboard. In this study the effects of density, adhesive content and particle size on withdrawal strength of particleboard made from Populus (Populus alba) particles have been studied. Three levels of density including 0.65, 0.7, and 0.75 g/cm3, three levels of adhesive content including 8, 9.5, and 11% and four levels of particles size including +5, -5 +8, -8 +12, and -12 mesh were used Moisture content of cake, press time, press temperature, press pressure were 12%, 5 min, 180 oC, and 35 kg/cm2 respectively. The results showed that particle size increased screw withdrawal resistance more than board density and adhesive percent, so there was a possibility to increase screw withdrawal resistance without increasing board density and adhesive percent. The highest withdrawal strength was obtained in particle board with density 0.75 g/cm3, adhesive content 11% and particle size +5 mesh.
اندازه ذرات، دانسیته تخته و درصد چسب از مهمترین فاکتورهای تعیینکننده خواص فیزیکی و مکانیکی تختهخردهچوب هستند. این پژوهش با هدف بررسی میزان تأثیرگذاری هر یک از سه متغیر دانسیته، درصد چسب و اندازه ذرات بر ظرفیت نگهداری پیچ در تختهخردهچوب ساخته شده از خردهچوب صنوبر (Populus alba) انجام شد. به این منظور از سه سطح دانسیته 65/0، 7/0، 75/0 گرم بر سانتیمترمکعب و سه سطح درصد چسب 8، 5/9 و 11 درصد و چهار سطح اندازه ذرات (5+)، (5-8+)، (8-12+) و (12-) مش استفاده شد. درصد رطوبت کیک 12، زمان پرس 5 دقیقه، دمای پرس 180 درجه سانتیگراد، فشار پرس 35 کیلوگرم بر سانتیمترمربع بودند. نتایج نشان داد که افزایش اندازه ذرات در مقایسه با افزایش دانسیته و درصد چسب به مقدار بیشتری بر ظرفیت نگهداری پیچ عمود بر سطح و لبه میافزاید و امکان افزایش ظرفیت نگهداری پیچ بدون افزایش دانسیته و درصد چسب وجود دارد. همچنین بیشترین ظرفیت نگهداری پیچ مربوط به تختههای با دانسیته 75/0 گرم بر سانتیمترمکعب، درصد چسب 11 درصد و اندازه ذرات 5+ مش بود.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Effect of ONP Recycled Fibers Use on the Properties of
Mixed Hardwoods Virgin Kraft Pulp
تأثیر استفاده از الیاف کاغذ روزنامه بازیافتی بر ویژگیهای
خمیر کرافت مخلوط پهنبرگان
69
84
217
FA
Journal Article
2012
07
16
This study has been conducted in order to investigate the effect of using ONP recycled fibers on the mechanical and optical properties of local mixed hardwoods kraft pulp at Iran Wood and Paper Industry (Chooka). ONP and virgin kraft pulp have been prepared from Chooka’s waste paper storage and pulping digester, respectively. ONP has been repulped in the common method as used by paper recycling industry. After determination of the initial freeness of each pulp, they have been separately refined to reach the appropriate freeness value required to produce kraft paper. The pulps, then, have been mixed at 90.10, 80.20, 70.30, 50.50 and 30.70 percentage rates of recycled fibers and virgin kraft pulp, respectively. According to the related standard test method, handsheets were made from each treatment and their mechanical and optical properties have been measured. The results were compared with those of control sample (100% virgin kraft) using ANOVA technique and classification of the means was done by Duncan test. Finally, to determine the best treatment, normalization equation was calculated. The results show that the values of tensile, tear, and burst indices, folding endurance and density of the combined papers have been increased compared with those of control sample, but the values of bulk, thickness, brightness and opacity of the combined samples have been decreased. The scores of the treatments indicate that 50 percent of recycled fibers can be used in the furnish to produce paper with suitable mechanical and optical properties.
این پژوهش بهمنظور تعیین اثر استفاده از الیاف کاغذ روزنامه بازیافتی بر ویژگیهای مکانیکی و نوری خمیر کرافت مخلوط پهنبرگان در صنایع چوب و کاغذ ایران انجام شد. کاغذهای روزنامه باطله از انبار کاغذ باطله و خمیر کرافت مخلوط پهنبرگان از دیگ پخت شرکت چوکا تهیه گردیدند. کاغذهای روزنامه به روش معمول در صنایع بازیافت کاغذ دوباره به خمیر کاغذ تبدیل شدند. بعد از تعیین درجه روانی اولیه هر یک از خمیرهای بازیافتی و دست اول، خمیرهای یاد شده بهصورت جداگانه پالایش شده تا به درجه روانی مناسب برای تهیه کاغذ کرافت برسند. سپس خمیرهای نام برده با نسبتهای 10/90، 20/80، 30/70، 50/50 و 70/30 بهترتیب برای خمیر بازیافتی و خمیر کرافت مخلوط پهنبرگان با یکدیگر مخلوط شدند. از هر یک از تیمارهای بالا، کاغذهای دستساز طبق استاندارد مربوطه ساخته شده و ویژگیهای مکانیکی و نوری آنها اندازهگیری و تعیین گردید. برای مقایسه ویژگیهای کاغذهای ترکیبی با نمونه شاهد (100 درصد خمیر کرافت) از آزمون تجزیه واریانس استفاده شد و سپس گروهبندی میانگینها به کمک آزمون دانکن صورت پذیرفت و در نهایت برای تعیین بهترین تیمار از معادله نرمالسازی استفاده گردید. نتایج نشان داد که با افزایش درصد خمیر بازیافتی، مقاومت به کشش، پاره شدن، ترکیدن، تاشدن و دانسیته کاغذهای بهدست آمده در مقایسه با نمونه شاهد کاهش یافته ولی بالک، ضخامت، درجه روشنی و ماتی افزایش مییابد. امتیازات متعلق به هر یک از تیمارهای آزمایشی نشان داد که از مقدار 50 درصد الیاف بازیافتی روزنامه در ترکیب با خمیر کرافت دست اول پهنبرگان میتوان استفاده کرد و کاغذی با ویژگیهای مکانیکی و نوری مطلوب بهدست آورد.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Determining and Comparing the Effective Criteria on the Selection of
Wood Products among Income Categories at Gorgan
شناسایی و مقایسه شاخصهای مؤثر بر انتخاب فرآوردههای چوبی
در گروههای درآمدی شهروندان گرگان
83
97
218
FA
Journal Article
2012
07
16
Acquiring of customers satisfaction is an important objective for manufacturers. Determining the factors affecting consumer choice of wood products is important in deciding the competition level and judging the market status. Besides determining and rating the consumption criteria using Analytical Hierarchy Process in 2010 the study can be guide for both policymakers and inventors in this industry. Consumption criteria for wood products were determined on the basis of opinions of experts, consumers, sale agencies and academic experts, and then were categorized in three classes of Economic, Technical and Consumption each of them including eight sub-criteria. The data gathered from 144 citizens of Gorgan were compared statistically with SPSS package after being rated as income quarters using Analytical Hierarchy Process technique of Expert Choice software. The results showed that, considering the economic criteria, as the consumers income decreases, the product price becomes more important. Among the technical criteria, product design and product durability are the most important for high-income quarter and other quarters, respectively. The analysis of consumption criteria revealed that convenience is the most important for the rich and decrease in preference with reduction of income. For maid-income clan color and appearance are important. Among the criteria, the economic ones are the most influenced in purchasing wood products. While for the high-income clan, technical criteria are of
ایجاد رضایت مشتری همواره بهعنوان یکی از هدفهای مهم تولید بهشمار میرود. تعیین شاخصهای مؤثر بر انتخاب فرآوردههای چوبی برای شرکتهای تولیدکننده محصولات چوبی، عامل مهمی برای تعیین سطح رقابت و انجام قضاوت درست وضعیت بازار محسوب میشود. پژوهش حاضر در سال 1388، ضمن شناسایی و رتبهبندی معیارهای مصرف، با استفاده از تکنیک تحلیل سلسله مراتبی میتواند بهعنوان راهنمای مناسب برنامهریزان و سرمایهگذاران این فرآوردههای ارزشمند مطرح باشد. معیارهای مصرف فرآوردههای چوبی با نظرسنجی از کارشناسان، تعدادی از مصرفکنندگان، نمایندگیهای فروش محصولات چوبی و صاحبنظران دانشگاهی شناسایی و در سه گروه، اقتصادی، فنی و مصرفی طبقهبندی گردیدند. آمار و اطلاعات جمعآوریشده از 144 شهروند ساکن گرگان پس از وزندهی در چارکهای درآمدی، مورد مقایسه قرار گرفت. نتایج نشان داد که در زیرمعیارهای اقتصادی، هرچه سطح درآمد مصرفکنندگان کاهش مییابد، قیمت کالا از اهمیت بالاتری برخوردار میشود. در خصوص معیار فنی، "طرح ساخت" در چارک درآمدی اول و "طول عمر" در بقیه چارکهای درآمدی بیشترین درجه اهمیت را به خود اختصاص دادهاند. نتایج تحلیل معیار مصرفی نیز نشان داد که شاخص "راحتی"، مهمترین معیار مصرفی در بین قشر پردرآمد بهشمار میآید و با کاهش سطح درآمدی، از ارجحیت آن کاسته میشود. ضمن آنکه "رنگ و نقش و نگار" در مقایسه بقیه معیارهای مصرفی در بین قشر متوسط اهمیت بالاتری دارد. در مجموع، از دیدگاه مصرفکنندگان، معیار اقتصادی مؤثرترین معیار در خرید محصولات چوبی محسوب میشود، در حالیکه، معیار فنی در گروههای درآمدی بالاتر بیشترین اهمیت را به خود اختصاص داده است و با کاهش درآمد، معیار فنی از برتری کمتر و در مقابل معیار مصرفی از ارجحیت بالاتری برخوردار میشود.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Investigation on Physical and Mechanical Properties of Medium
Density Fiberboard (MDF) Made from Acacia salicina
بررسی خصوصیات فیزیکی و مکانیکی تختهفیبر با دانسیته متوسط (MDF)
ساخته شده از چوب گونه آکاسیا (Acacia salicina)
97
110
219
FA
Journal Article
2012
07
16
In this research the utilization of Acacia wood (Acacia salicina) in medium density fiber board production was investigated. Sample boards were made from Acacia fibers at two resin contents (10, 12%), two press temperatures (175, 185 ˚C) and three press times(3, 4, 5 min). The results were analyzed based on a complete randomized design (CRD) under a factorial experiment. Results revealed that increase of resin content had a positive effect on MOR and MOE and thickness swelling of MDF. At 12% resin content, MOR and MOE were respectively determined as 18.97 MPa and 1912 MPa. Also thickness swelling after soaking in water for 2 and 24 hours decreased from 15.87 and 20.96% to 10.76 and 16.49%, respectively. Internal bond strength (IB) was higher at 4 min. press time than 3 and 5 min. The IB of the boards, which were made at 4 min press time, was determined as 0.63 MPa. In general, the results showed the possibility of using Acacia wood in MDF production with proper physical and mechanical properties.
این پژوهش با هدف بررسی امکان استفاده از چوب گونه آکاسیا (Acacia salicina) در ساخت تختهفیبر با دانسیته متوسط (MDF) صورت گرفت. به این منظور از الیاف بهدست آمده از چوب گونه آکاسیا تحت دو میزان مصرف چسب (10 و 12 درصد)، دو دمای پرس (175 و 185 درجه سانتیگراد) و سه زمان پرس (3، 4 و 5 دقیقه) تختههای آزمونی در قالب 12 تیمار و در مجموع 36 تخته ساخته شده و نتایج نیز در قالب طرح آماری کاملاً تصادفی تحت آزمایش فاکتوریل تجزیه و تحلیل شدند. نتایج آزمون تجزیه واریانس نشان داد که اثر مستقل مصرف چسب بر روی مقاومت خمشی، مدول الاستیسیته و واکشیدگی ضخامت 2 و 24 ساعت معنیدار بوده و با افزایش میزان مصرف چسب ویژگیهای یاد شده بهبود مییابند. افزایش مصرف چسب از 10 به 12 درصد مقاومت خمشی را از 87/16 به 97/18 مگاپاسکال و مدول الاستیسیته را از 1705 به 1912 مگاپاسکال افزایش و واکشیدگی ضخامت پس از
2 و 24 ساعت غوطهوری در آب را بهترتیب از 87/15 به 76/10 درصد و 96/20 به 49/16 درصد کاهش داد. زمان پرس نیز دارای اثر مستقل معنیداری بر روی مقاومت چسبندگی داخلی تختهها میباشد، بهطوریکه با افزایش زمان پرس از 3 به 4 دقیقه این ویژگی از 49/0 به 63/0 مگاپاسکال افزایش و سپس با افزایش زمان پرس به 5 دقیقه به 52/0 مگاپاسکال کاهش مییابد. همچنین نتایج تجزیه واریانس بیانگر تأثیر متقابل مصرف چسب و دمای پرس بر روی مقاومت خمشی و واکشیدگی ضخامت 2 و 24 ساعت تختهها میباشد. تأثیر متقابل دمای پرس و زمان پرس نیز بر روی مقاومت خمشی معنیدار بوده بهطوریکه بیشترین مقاومت خمشی در دمای پرس 185 درجه سانتیگراد و زمان پرس 3 دقیقه بهدست آمده و برابر با 97/18 مگاپاسکال میباشد. نتایج بهدست آمده بیانگر آن است که امکان تولید MDF از گونه چوب آکاسیا سالیسینا با خواص لازم وجود دارد.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Comparative Construction Costing of Prefabricated
Aluminum-and Masonry Wood dry Kilns
هزینهیابی مقایسهای احداث کورههای چوب خشککنی پیشساخته
آلومینیومی و ساخته شده با مصالح ساختمانی
111
125
220
FA
Journal Article
2012
07
16
The successful management in construction costing of wood dry kilns is an advantageous approach which brings us not only the assurance in service profitability but also gives rise customer’s satisfaction. The construction costing of two types of wood dry kilns, namely, prefabricated aluminum-and masonry kilns with normal operation temperature was studied. For this purpose, the construction, depreciation and maintenance costs of the kilns were determined via field trip tours and interviewing with kiln manufacturers and wood drying industry owners. The calculated costs were based on the performance of an automatic wood dry kiln which could control drying conditions (relative humidity, temperature, air circulation and ventilation) and continuously measure the wood moisture content. Consequently, the costs were estimated as a percentage of total costs. The results showed that the construction costs for masonry kilns were less than those for the prefabricated aluminum kilns. In contrast, the depreciation and maintenance costs for masonry kilns were greater than those for the prefabricated aluminum ones. Overall, the construction of prefabricated aluminum kilns are more profitably commercial in prolonged usage.
مدیریت سیستمهای هزینهیابی احداث کورههای چوب خشککنی یکی از راهکارهایی است که پیادهسازی و اجرای صحیح آن ضمن کسب اطمینان نسبت به کفایت میزان سودآوری خدمات، باعث افزایش رضایتمندی مشتریان میشود. در این پژوهش هزینهیابی احداث دو نوع کوره چوب خشککنی با دمای عملکرد متوسط، کوره پیشساخته آلومینیومی و ساخته شده با مصالح ساختمانی برای بررسی توجیهپذیری اقتصادی استفاده از این نوع کورهها، هدف این مطالعه بوده است. برای این منظور، با روش میدانی و مصاحبه با صاحبان صنایع چوب خشککنی و سازندگان کوره، هزینههای مربوط به احداث کورهها و نیز هزینههای استهلاک و تعمیر و نگهداری در این کورهها مورد مطالعه قرار گرفت. هزینه براساس شرایط یک کوره ایدهآل چوب خشککنی تمام خودکار با امکان تامین و کنترل شرایط داخل کوره (رطوبت نسبی، درجه حرارت، گردش هوای گرم و تهویه) و کنترل پیوسته رطوبت چوبها تعیین و محاسبه گردید. به دنبال این بررسی و استخراج هزینهها، میزان هر هزینه بهصورت درصدی از میزان کل هزینهها نمایش داده شد. نتایج نشان داد که هزینه احداث کورههای ساخته شده با مصالح ساختمانی کمتر از هزینه احداث کورههای پیشساخته آلومینیومی است. در مقابل، هزینههای استهلاک و تعمیر و نگهداری در کورههای ساخته شده با مصالح ساختمانی بیشتر از مقدار این هزینهها در کورههای پیشساخته آلومینیومی بود. اما در درازمدت کورههای پیشساخته آلومینیومی مقرون بهصرفهتر میباشد.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Comparison of Soda and Kraft Pulp Properties of Populus deltoides Sapwood and Heartwood
مقایسه ویژگیهای خمیر کاغذ سودا و کرافت از برونچوب و درونچوب صنوبر دلتوئیدس
125
138
221
FA
Journal Article
2012
07
16
This study was conducted to compare the yield and strength properties of soda and kraft pulp produced from Populus deltoeides sapwood and heartwood. Initially fiber length, lignin content in both sapwood and heartwood were measured. Then from either sapwood or heartwood pulps were prepared with using soda and kraft processes, Handsheets were made from this pulp and mechanical properties were measured. The results showed that fiber length in heartwood is shorter than sapwood. For both sapwood and heartwood pulps residual lignin content and kappa number of the pulps made by kraft process were higher than those for soda process. Also kappa number in the kraft and soda processes from heartwood was less than sapwood. The yield of soda and kraft processes from heartwood was lower than sapwood. This study also showed that tensile, tear and burst strength of the pulps made by kraft process were higher than relevant strength for soda process and the sapwood pulps were stronger than heartwood.
این پژوهش با هدف مقایسه بازده و ویژگیهای مقاومتی خمیر کاغذ سودا و کرافت از درونچوب و برونچوب صنوبر دلتوئیدس انجام گرفت. ابتدا طول الیاف و مقدار لیگنین درونچوب و برونچوب اندازهگیری شد. تحت شرایط پخت یکسان با استفاده از فرایندهای سودا و کرافت خمیرهای موردنظر تهیه گردید. مقدار لیگنین باقیمانده در خمیر کاغذ از دو بخش در هر دو فرایند سودا و کرافت اندازهگیری شد. سپس کاغذهای دستساز از هر یک از تیمارها ساخته و ویژگیهای مکانیکی آنها اندازهگیری گردید. نتایج نشان دادند که طول الیاف در بخش برونچوب بیشتر از درونچوب و مقدار لیگنین بخش برونچوب کمتر است. عدد کاپا و مقدار لیگنین باقیمانده در خمیر کاغذها از دو بخش درونچوب و برونچوب در خمیر کاغذ کرافت کمتر از خمیر کاغذ سودا بوده و همچنین این دو فاکتور برای هر دو پخت در بخش درونچوب بیشتر از بخش برونچوب میباشد. بازده خمیر کاغذ فرایند کرافت کمتر از سودا و در بخش درونچوب برای هر دو پخت کمتر از برونچوب است. نتایج بهدست آمده از مقاومتهای مکانیکی کاغذهای دستساز نشان داد که مقاومت در برابر کشش، مقاومت در برابر ترکیدن و مقاومت در برابر پاره شدن کاغذهای دستساز بهدست آمده از فرایند کرافت بیشتر از سودا و بخش برونچوب هر دو پخت بیشتر از درونچوب میباشد.
دانشگاه علوم کشاورزی و منابع طبیعی گرگان
پژوهشهای علوم و فناوری چوب و جنگل
2322-2077
17
4
2012
07
16
Comparison of Regeneration and Biodiversity of Trees on Cut and Fill Edges of Forest Road (Case Study: Chamestan and Lavige Forests, Noor)
مقایسه زادآوری و تنوع زیستی درختان در ترانشه خاکبرداری و خاکریزی جاده جنگلی با افزایش فاصله از آن (مطالعه موردی: جنگلهای چمستان و لاویج، نور)
139
153
222
FA
Journal Article
2012
07
16
The evaluation of the edge effects of forest roads on ecosystem is very useful to understand changes from forest road. With this regard, in this research the effect of main forest road construction on regeneration and biodiversity of established trees in edge of forest road was investigated at 35 m distance into forest area. An existing 10 years old road segment, with same physiographic properties, volume per hectare and species composition along the road was selected in Chamestan and Lavige Forests in Mazandaran province. Six linear transactions were set on the fill and cut edge (three transects were set on fill and others on cut edges). Trees’ regenerations were recorded on linear transactions, within circular sample plots by 2 m radius at (2.5, 7.5, 15, 25, 35 m) distances from the road edge. The results showed, no significant differences between trees’ regenerations in the cut and fill edges up to 35 m into the forest area at 0.05 level. However, the average trees’ regenerations in the fill edge were more than the cut edge along the forest road. Maximum and minimum trees’ regenerations density, were recorded in 7.5 and 2.5 m distances from the road edge. The result showed that the maximum densities of trees’ regenerations were belonged to Acer spp and Carpinus betulus species in fill edge and Diospyrus lotus species in cut edge. The comparison of the species diversity and species richness indexes indicated that, the maximum values of species diversity indexes (both Shannon-wiener and Simpson (were in 7.5 m distance and richness indexes (Minhinick and Margalef) were in 2.5 and 15 m distances from the road edge. However, no significant differences were found between indexes in the cut edge and fill edge at 35 m distance (P>0.05).
برآورد اثرات حاشیه جادههای جنگلی برای درک تغییرات ناشی از شبکه جادههای جنگلی بر روی اکوسیستم از اهمیت بالایی برخوردار است. به این منظور در این پژوهش تأثیر ساخت یک جاده درجه دو جنگلی بر روی زادآوری و تنوع زیستی درختان استقرار یافته تا فاصله 35 متری از لبه جاده بررسی شده است. بخشی از جاده درجه دو جنگلی که بهمدت تقریباً 10 سال قبل ساخته شده بود، در جنگلهای چمستان و لاویج با داشتن شرایط فیزیوگرافی، حجم در هکتار و ترکیب گونهای یکسان در کل طول جاده انتخاب شد. تعداد 3 خط نمونه در ترانشه خاکریزی و 3 خط نمونه در ترانشه خاکبرداری طراحی گردید. زادآوری درختان حاشیه جاده در قطعات نمونه دایرهای شکل در فواصل (5/2، 5/7، 15، 25 و 35 متر) از لبه جاده بر روی هر یک از خط نمونهها بررسی شد. نتایج پژوهش نشان داد که، اختلاف میانگین زادآوری در دامنههای خاکبرداری و خاکریزی تا عمق 35 متری داخل جنگل معنیدار نمیباشد (05/0P).